Ereada Amethyst and Gemstone Mats and Heating Pads are equipped with Digital Controllers with AUTO EMI function automatically detecting and transferring absorbed EMFs spikes into the wall socket “ground pin” for Earthing.
Controllers for Ereada Mini Mats
Brown Ereada Amethyst Mini Mat and Gemstones Mini Mat controllers
This controller allows to adjust the temperature of inner low EMF heating systems with 1°C increment in the range 86°F~158°F (30°C-70°C).
Heat levels are displayed as Celsius Temperature on the controller screen.
Ereada Mini Mat Controller without N.P. function has either 1 or 8 hours procedure time settings to chose.
The Timer should be activated to start heating and all other functions. It auto-shuts off the mat after preset time expires.
Q-2000NP Controller for Ereada Mini Mats with Silver Fiber Negative Potential Layer
Other controller used in Ereada Mini Mats with N.P. function is Q-2000NP Controller.
This controller allows to adjust the temperature of inner low EMF heating systems with 5°C increment in the range 86°F~158°F (30°C-70°C).
It activates and auto-shuts off Negative Potential Electrostatic Field after 30 minutes.
This controller does not have time settings but has built-in safety timer set to automatically turn the mat off in 8 hours.
Purple Ereada Mini Mat Controller with Photon function
This controller activates Red Light Phototherapy LEDs for 1 hour periods each 4 hours of mat active session for 2 cycles with auto shut-off after 8 hours.
Controller does not have time settings but has built-in safety timer set to automatically turn the mat off in 8 hours.
It has a a temperature dial to chose one of seven temperature settings in the range between 86°F~158°F (30°C-70°C) displayed as levels 1-7 on the controller screen.
Controllers for Ereada Compact PRO and larger Mats
All Controllers for Compact Pro, Professional, Single and Queen Amethyst Mats and Gemstone Mats have a temperature dial to chose one of seven temperature settings in the range between 86°F~158°F (30°C-70°C) displayed as levels 1-7 on the controller screen.
| LEVEL 1 | 86°F or 30°C (Sleeping mode) |
| LEVEL 2 | 98°F or 36°C (Low mode) |
| LEVEL 3 | 110°F or 43°C (Low medium mode) |
| LEVEL 4 | 120F or 49C (Medium mode) |
| LEVEL 5 | 133°F or 56°C (Medium High mode) |
| LEVEL 6 | 145°F or 63°C (High mode) |
| LEVEL 7 | 158°F or 70°C (Highest mode) |
Big ventilated controllers for Brown Ereada Compact Pro Mats and larger with N.P. function activate it and auto-shut off Negative Potential Electrostatic Field after 60 minutes.
These big controller have either 4, 8 or 12 hours or 3, 6 or 9 hours time settings to chose. The Timer should be activated to start heating and all other functions. Controller auto-shuts off the mat after preset time expires.
Big Mat Controllers with Bio Photon function activate Red Light LEDs with 1 hour cycles each 4 hours, auto-shuts off after 2 cycles.
Big Mat Controllers with Bio Magnetic PEMF function activate pulsed magnetic therapy with 20 min cycles each 2 hours, auto-shuts off after 4 cycles.
Purple Ereada Mat and Gemstone Mat bigger then Compact Pro are featured with controllers with air ion function which auto-shuts off after 1 hour of operation.
Double Zone Controller for Queen Size Ereada Mats allows to adjust temperature and procedure time and operate these functions in each zone separately.
All functions can be manually activated or stopped any time by pressing the appropriate button.
CONTROLLER ERRORS TROUBLESHOOTING
- Sometimes all controllers may produce some buzz or humming noise which is quite normal. But if the noise becomes louder and intolerable, please, contact us for replacement. Remember that it is always recommended to connect controller to the socket through surge suppressor, automatic voltage regulator or UPS to extend it’s life.
- The most frequent reason for the controller to show errors is the connection problem. Reconnection usually helps to reload the controller and eliminate errors. Disconnect the plug of the controller from the power socket first and then from the mat connection terminal. After this first reconnect the mat tightly to the controller and second plug it into electricity socket again. Be sure that the socket has electrical power, it can be tested by any other device.
- If controller display shows “OF” or errors try to activate timer first. If it does not help turn ON/OFF and try reconnection.
All products, specifications and data are subject to change without notice to improve reliability, function or design